The Navigatrix has been updated. The new website can be found at navigatrix.net.
|
Page 1 of 1
|
[ 18 posts ] |
|
Author |
Message |
svattila
|
Post subject: Iridium doesn`t connect...
|
|
Joined: 21 May 2013, 14:53 Posts: 93
|
Hello, NX-ers! I have bveen using Wvdial to connect to the internet using my iridium phone since years, but now i have a problem which I can not resolve.... I recently changed my SIM card, and the phone works fine using this new sim card, but every time I try to connect to the internet, the dialer gives the command ATDT008816000025, waits a little bit, and then returns: No Carrier! Trying again....... and so on.... but it never connects. The only difference between the old and the new SIM card is that while the old one dialed the number immediately after punching the numbers in, the new one gives me the remaining account balance and expiration date after dialing the number. This statement takes about 10 seconds... To me it looks like the dialer should wait for a longer time, to pass this statement before it could detect a carrier, please correct me if I am wrong... Any ideas how to solve this problem? If I manually dial 008816000025, and wait until the lady finishes with the account balance, I can clearly hear the chirrupping of the carrier signal.... Thank you! Adrian Attachment:
2015-01-25_151553_600x339.png [ 85.97 KiB | Viewed 23718 times ]
|
|
Top |
|
|
Moe
|
Post subject: Re: Iridium doesn`t connect...
|
|
Joined: 04 Nov 2010, 20:51 Posts: 1062
|
A stab in the dark Adrian, Code: gksu medit /etc/ppp/options Down towards the bottom of the file is Quote: # Wait for up n milliseconds after the connect script finishes for a valid # PPP packet from the peer. At the end of this time, or when a valid PPP # packet is received from the peer, pppd will commence negotiation by # sending its first LCP packet. The default value is 1000 (1 second). # This wait period only applies if the connect or pty option is used. #connect-delay <n> Remove the # on the last line to something like Code: connect-delay 10000 for a 10 second pause. Save and test. Or, you could try adding Code: Dial Timeout =10 to end of the wvdial.conf file you're using. Save and test. Increasing/decreasing the value to suit. Your choice of either one modification or the other, but not both.
|
|
Top |
|
|
svattila
|
Post subject: Re: Iridium doesn`t connect...
|
|
Joined: 21 May 2013, 14:53 Posts: 93
|
Hello, Moe! Ayay. I tried both methods, no success. I tried both files, from 5 to 40 seconds of delay, but no difference in the frequency of the No Carrier! Messages... After each attempt to call, it comes back with the No Carrier! message, way before the set -say 30 seconds have expired. I Think my problem is before this, I think at the dialing stage. The phone gives this li-la-li sound every time right after ATDT008816000025 command is given... it is like he is calling the wrong number, or gives the wrong dial command, way before they would wait for the carrier.... Any ideas? Adrian
|
|
Top |
|
|
Moe
|
Post subject: Re: Iridium doesn`t connect...
|
|
Joined: 04 Nov 2010, 20:51 Posts: 1062
|
Oh, bugger, the cursed li-la-li sound....;-) Does it make the li-la-li sound when you hand dial? Oh, and you did edit those files as root? gksu medit /blah/blah/blah, right? Hang on...Is this dialing, and hanging up with the lovely lady recording telling you about your balance, or is it picking up and saying there is no carrier (dial tone) to know when to begin to dial? There are a few 'dirty' hacks you could try... Adding Code: Carrier Check = no to your wvdial.conf
|
|
Top |
|
|
svattila
|
Post subject: Re: Iridium doesn`t connect...
|
|
Joined: 21 May 2013, 14:53 Posts: 93
|
Hello, Moe! I tried Carrier Check = no in the .conf file, but it still waits for the carrier... When I hand dial the number for the data service, it just tells me my account balance, then rings the server, and the server starts singing the carrier sound in my ear... When Wvdial tries to dial, it always runs into the cursed li-la-li sound Yes, when I edited the said files I had sudo rights.... What this problem could be? Could I just manually dial the number, and tell the computer to start listening when i got the carrier signal? Or any other ideas? Adrian
Attachments: |
2015-01-29_151719_1360x768.png [ 201.12 KiB | Viewed 23708 times ]
|
|
|
Top |
|
|
Moe
|
Post subject: Re: Iridium doesn`t connect...
|
|
Joined: 04 Nov 2010, 20:51 Posts: 1062
|
If I'm hearing you correctly the la-li-la is an error tone. I just don't where it's coming from, nor do I know how you could use it like the old acoustic couplers where we use to dial and when it started to squeal-slap it into the holder. Try changing Init2 to Code: Init2 = ATS9=10V1X4E1Q0&c1 S9 Carrier Detect Response Time 1–255 tenths of a seconds 6 (0.6 second) setting it to 10 give a one second delay to figure out the carrier. X4, well the X4 " Usually adds both busy signal and dial tone detection" "Usually" comes from the original documentation of Hayes Command Set, the alphabet soup in the init lines Give changing the init2 a go, and in the meantime I'll charge up the phone, and see if I can play along in the next few days.
|
|
Top |
|
|
svattila
|
Post subject: Re: Iridium doesn`t connect...
|
|
Joined: 21 May 2013, 14:53 Posts: 93
|
I changed the Init line in the config file. Now it does make a difference. Now it waits longer before quitting with the li-la-li errror code... hmm... it is getting frustating. Adrian
|
|
Top |
|
|
Moe
|
Post subject: Re: Iridium doesn`t connect...
|
|
Joined: 04 Nov 2010, 20:51 Posts: 1062
|
The good thing is you know you're messing with the right configuration file;-) I'm asking myself two questions: 1) What is different about the old sim and the new sim? 2) What is the difference between hand dialling and machine dialling? I'm making some assumptions that hand dialling is hiding delays in the system. For example, checking the account of the reseller, who checks if you still have the go-ahead. Hand dialling is slow, a few milliseconds here, a few there, no one is the wiser. On the other hand machines don't hesitate unless a lag is built in, or inherent, to the system. A machine on one end will dialling away while the other end is still checking permissions, la-li-la, I'm not ready. It could be the speed of the tones (DTMF) themselves, how fast the dial. Quote: S11 DTMF Tone Duration Range: 50–255 milliseconds Default: 95 milliseconds The default of 95 milliseconds might be too fast compared to hand dialling, that is. We don't really know because we're guessing, and when you hand dial, and an assumed slower hand dialling speed might be enough, S11=150 added to the init script could be the trick. Then again, the cumulative wait time of an extra 55 milliseconds per tone might push you off the deep end.
|
|
Top |
|
|
svattila
|
Post subject: Re: Iridium doesn`t connect...
|
|
Joined: 21 May 2013, 14:53 Posts: 93
|
Hello, Moe!
Where do I insert this command? I mean which Init line I have to modify? Is the text to be inserted looks like this: S11 = 200 I think we are getting closer to the solutrion... Lets see.
Adrian
|
|
Top |
|
|
svattila
|
Post subject: Re: Iridium doesn`t connect...
|
|
Joined: 21 May 2013, 14:53 Posts: 93
|
Hello, Moe!
I added S11=150 to the Init line, but it did not help my problem. What this problem could be? We are planning to go to the sea for like 90 days very soon, and it would be nice to receive weather data. Any other suggestions?
Adrian
Attachments: |
2015-01-31_080430_1360x768.png [ 186.02 KiB | Viewed 23698 times ]
|
|
|
Top |
|
|
Moe
|
Post subject: Re: Iridium doesn`t connect...
|
|
Joined: 04 Nov 2010, 20:51 Posts: 1062
|
Isn't that the way it always goes...down to the crunch and then some snafu. It was the reason we got the sat phone to begin with. It always seemed the SSB would spit up the week, or so, before we left. So to help diagnose your difficulty, I drag out the phone. I forgot with Iridium, after a period of time, any remaining minutes on the sim card disappeared. Iridium, however, did not forget...bugger! there were over 100 minutes left. To add insult to injury, I am no closer to figuring your situation out. Who is the reseller of your sim? Maybe we can find something there. In the meantime, place a comma , at the beginning of the phone number Code: Phone = ,008816000025 and cross your fingers, or the Hungarian equivalent.
|
|
Top |
|
|
svattila
|
Post subject: Re: Iridium doesn`t connect...
|
|
Joined: 21 May 2013, 14:53 Posts: 93
|
Hello, Moe!
I`ve bought the card from assystems in Tahiti... Seems like all the other sims I purchased before.... Well, I`ve tried with the comma (,) but it still doesn`t connect. I have to go on the sea for 2 days, I will check again later, meanwhile I will experiment with it, too....
Thank you for your help, Moe!
|
|
Top |
|
|
Moe
|
Post subject: Re: Iridium doesn`t connect...
|
|
Joined: 04 Nov 2010, 20:51 Posts: 1062
|
Those dang Customs and Importation laws.... Good luck. I spent the morning going over the original source from University of New South Wales professor, Michael Ashley. http://newt.phys.unsw.edu.au/~mcba/iridiumLinux.html He wrote the original wvdial script for his phones in Antarctica, and had the forethought to have local copies of his reference sources in case they 'disappear from the original sites'. I've gone through his references, and a few other on the 'net, and I'm no more the wiser as the cause of your troubles. Your phone is a 9500 with a serial/usb adapter, right? (in some of the nitty-gritty there's a difference between 9500/9505 in compliance with AT commands...go figure...) I'll put it on the back burner, but anything I have to add at this point is just more blind speculation. Sorry.
|
|
Top |
|
|
Moe
|
Post subject: Re: Iridium doesn`t connect...
|
|
Joined: 04 Nov 2010, 20:51 Posts: 1062
|
One question I had was, "Does this new sim have data capabilities on the account?" From Iridium's troubleshooting guide, The SIM card must be provisioned for data.http://newt.phys.unsw.edu.au/~mcba/iridium/Dial-Up%20Data%20Troubleshooting.pdf wrote: Phone is registered, but cannot make a dial-up data connection. • Verify that the phone is displaying good signal strength. The SIM card must be provisioned for data. If in doubt, contact your Service Provider. Check the software version in the phone by pressing *#91# on the keypad. The Motorola 9500 must show software version INC0620 or later. The Motorola 9505 must show software version LAC109G or later. The Motorola 9520 must show software version RAC0620 or later. (Newer data-capable versions may be released from time to time, and will be indicated by a higher numerical sequence.) Check the cable connections. Check to see that the dialed phone number is accurate, and that it was dialed in international format (00 + Country Code + Area Code/Phone Number). For example, if you are dialing an ISP in Tempe, Arizona, USA, you would enter 00 1 480 555 5555, where 1 is the country code and 480.555.5555 is the ISP’s telephone number. You can verify that you are dialing the correct number by dialing the number as a voice call from your Iridium phone. You should hear your ISP’s modem tones if dialed properly. • Verify that your settings have not changed (modem properties, phone number, user name, password, etc.) Is your Iridium handset dialing? While dialing, the Iridium handset blinks “Data Call in Progress”. If not, cycle the power on the phone to reset it. ...and so it goes. The phone number is correct; the firmware in the phone is fine; I'm just not sure about the rest. I'd also recommend http://newt.phys.unsw.edu.au/~mcba/iridium/ISU_AT_Command_Ref_v2.7.pdf if you want to make your brain hurt...but it could just be a voice-only sim. Assystem Polynésie was too confusing for me to untangle.
|
|
Top |
|
|
svattila
|
Post subject: Re: Iridium doesn`t connect...
|
|
Joined: 21 May 2013, 14:53 Posts: 93
|
Hello, Moe!
My phone is a 9505, and the software version is the LAC109G. It connects to the computer through the serial port, no Serial to USB converter is being used. I`ve sent an email to assystems in Tahiti, to ask them about the data permissions for my sim card. Let`s hope they come back with something useful.
Adrian
|
|
Top |
|
|
svattila
|
Post subject: Re: Iridium doesn`t connect...
|
|
Joined: 21 May 2013, 14:53 Posts: 93
|
Hello, Moe!
I got the response from assystems and -yes- he forgot to activate the data service.... Now that he did activate it it works fine with the original config file. One little problem remains: Every time I turn the computer on, it forgots the settings. So to use the satphne I have to do this exact sequence: Turn on computer, connect and power up satphone run sudo wvdialconf /etc/wvdial.conf wvdialconf gets everything right, exept the speed, so I have to sudo gedit /etc/wvdial.conf and change 11500 to 19200 then save it. Now when I click on the stellite icon, it connects and works fine. But if I turn off the computer, I will have to do again the wvdialconf and therefore the gedit, too. I looked into it, and the wvdial.conf file gets saved OK, with the 19200, but it still does not work, only after re-running wvdialconf .... Any ideas why this happens?
Adrian
|
|
Top |
|
|
Moe
|
Post subject: Re: Iridium doesn`t connect...
|
|
Joined: 04 Nov 2010, 20:51 Posts: 1062
|
Adrian would you run Code: ls -lisa /etc/wvdial* It will look something like Quote: moe@io:~$ ls -lisa /etc/wvdial* 524586 4 -rw-r--r-- 1 root root 230 Aug 13 2014 /etc/wvdial.conf 524587 4 -rw-r--r-- 1 root root 243 May 14 2014 /etc/wvdial.conf.iridium0 524588 4 -rw-r--r-- 1 root root 251 May 14 2014 /etc/wvdial.conf.iridium1 524589 4 -rw-r--r-- 1 root root 230 Jun 13 2013 /etc/wvdial.conf.isatphone0 524590 4 -rw-r--r-- 1 root root 234 May 14 2012 /etc/wvdial.conf.isatphone1
we are just checking ownership ( root root) and permissions ( rw-r--r--).
|
|
Top |
|
|
svattila
|
Post subject: Re: Iridium doesn`t connect...
|
|
Joined: 21 May 2013, 14:53 Posts: 93
|
Here is the return: nx@navigatrix:~$ ls -lisa /etc/wvdial* 536722 4 -rw-r--r-- 1 root root 294 Feb 27 08:54 /etc/wvdial.conf 548649 4 -rw-r--r-- 1 root root 266 Feb 4 13:25 /etc/wvdial.conf.iridium0 522540 4 -rw-r--r-- 1 root root 274 Feb 4 13:26 /etc/wvdial.conf.iridium1 522541 4 -rw-r--r-- 1 root root 230 Jun 12 2013 /etc/wvdial.conf.isatphone0 522542 4 -rw-r--r-- 1 root root 234 May 13 2012 /etc/wvdial.conf.isatphone1
Adrian
|
|
Top |
|
|
|
Page 1 of 1
|
[ 18 posts ] |
|
|